Can be used as an elastomeric single-ply roofing membrane for new construction and re-roofing applications.
May be installed in Ballasted and Fully Adhered roofing systems.
Find a Distributor
Features & Benefits
- Multiple widths and lengths
- 45, 60, 90 mil thickness
- Fully adhered and ballasted systems only
- Increased Fire-rated sheet available
- Most often installed as fully adhered
- Up to a 30 year system warranty available
- Approved for use with Mule-Hide Acrylic Water Base Bonding Adhesive for up to a 20 year system warranty
- Dusted or clean sheets available
- Pre-Taped with 3" or 6" tape available
EPDM Acrylic Water Base Adhesive
EPDM AP Bar Base Attachment
EPDM Blow-Out Patch
EPDM Curb Flashing
EPDM Drip Edge
EPDM Field Sheet Repair
EPDM Field Wrapped Pipe
EPDM In-Seam Tape
EPDM Inside Corners
EPDM Outside Corners
EPDM Pipe Boot
EPDM Pre-Fabricated Sealant Pocket
EPDM Roof Drain
EPDM T-Joint Patch
EPDM Wall Flashing with RMS
Insulation - Mechanically Attached
ShapeShift Pitch Pan
What is a suitable substrate for EPDM Membrane with Acrylic Water-Base Bonding Adhesive application?
Plywood, OSB, HD Wood Fiberboard, DensDeck® Prime or SECUROCK®
What are the Warranty Fees for EPDM Roofing Systems?
Fees vary depending on the type of warranty desired. Current Fees are listed on Mule-Hide Warranty Application forms.
Does the contractor need to provide material invoices along with Warranty Applications?
Specific warranties may require submission of material invoices.
Does Mule-Hide require a total tear-off for Labor & Material Warranties?
No, this is not required, but all areas of wet insulation must be replaced with new, dry, similar material, specific warranties may require an independent moisture scan of the roof.
Does Mule-Hide offer any pre-job “walk the roof” or job starts?
Yes, Mule-Hide Territory Managers offer these services.
Can I use Mule-Hide Acrylic Water Base Bonding Adhesive to adhere flashings?
Mule-Hide Bonding Adhesive (solvent based), Aquabase 120 (water based) or Low VOC Bonding Adhesive are used as a contact adhesive to adhere flashings to acceptable vertical surfaces.
What fasteners should be used for insulation attachment on a steel or wood deck?
Drill Point Fasteners (#12) should be used with 3" Insulation Plates.
What is In-Seam Tape?
In-Seam Tape is a cured, butyl based, two-sided adhesive tape that bonds on contact and is used to seam and eliminate applicator inconsistencies & voids. When applied properly (Mule-Hide Tape Primer must be used), it provides the fastest way to achieve strong, long lasting, watertight field seams.
What is Cured Cover Tape?
Cured Cover Tape is a length of EPDM, factory-bonded to a cured butyl adhesive tape that is highly resistant to the most extreme weather & use situations. It is used to strip in gravel stops and drip aprons metal edging). When applied properly (Mule-Hide Tape Primer must be used), it provides a long lasting, high-performing seal. Cured Cover Tape is also used to strip in field seams, rows of seam plates or batten bars for membrane attachment.
What if I need to prove Mule-Hide EPDM meets a written specification or complies with a UL, FM or other code requirement?
Just provide Mule-Hide with the following information:
A copy of the specification
Name & address to whom the letter should be addressed
Your phone & fax number
What is the UL/FM requirement?
Insulation type and thickness?
Membrane and system?
Building location and height?
Do I need walk pads for a large commercial roofing project?
Walk pads are always recommended. Mule-Hide offers walk pads for each system/membrane type we sell.