Skip to content
PVC KEE HP Fleece Back

PVC KEE HP Fleece Back

MuleHide PVC KEE HP Fleece Back Membrane is used in fully adhered roofing systems in new construction, reroofing and recover (retrofit) applications. The polyester fleece backing enhances the puncture resistance of the membrane, and can also serve as a built-in separation layer for rough surfaces or existing asphalt-based roofing systems. The system must be installed over acceptable roof insulation or other suitable substrate.

System

PVC
  • Welds quickly and consistently
  • Durable scrim reinforcement offers superior puncture resistance
  • UV, ozone and oxidation resistance
  • Energy efficient
  • Enhanced chemical resistance
  • Low temperature flexibility
  • 55 Mil fleece backing
  • Meets UL Standards
  • Meets C-UL Standards
  • Meets FM Standards
  • Meets CCMC Standards
  • Meets Miami-Dade-County Standards
  • Meets Florida-Building Standards
  • Meets CRRC Standards
  • Meets CA-Title-24 Standards
  • Meets ICC-ES Standards

Documents

PDS PVC Systems KEE HP Fleece Back Membrane
View
SDS - Statement for Article Products
View

CCMC - Canadian Construction Materials Centre evaluation for PVC Systems
View
Florida Product Approval - HVHZ - PVC Systems
View
Florida Product Approval - PVC Systems
View
ICC-ESR Report - Adhered and Mech. Attached EPDM Systems, TPO Systems & PVC Systems
View
TDI - Texas Department of Insurance - TPO Systems & PVC Systems MA over wood
View
UL - Impact resistance ratings for PVC Systems
View
UL - Overview of UL Listings for PVC Systems
View

Hail Coverage - Procedures and Requirements
View
Letter of Compliance Application- Photovoltaic Installation on Mule-Hide Warranted Roof
View
Procedure for Inclusion of Photovoltaic Anchor Flashings
View
PVC Cross Reference Chart
View
PVC Metal Retrofit
View
PVC Pocket Guide
View
PVC Pocket Guide (Spanish)
View
PVC Systems Contractor Brochure
View
Sell Sheet - Fleece Back Recovery System
View
Sell Sheet - Why Choose PVC
View
Single-Ply Roofing Accessories Guide
View

Design Enhancements - Single-Ply Membranes
View
Design Summary - PVC Fleece Back Systems 10 or 15 year Fully Adhered
View
Design Summary - PVC Systems 10 or 15 year Fully Adhered
View
Design Summary - PVC Systems 10 or 15 year Mechanically Attached
View
E-Z Commercial Warranty Application - Material Only
View
Warranty - Notice of Completion
View
Warranty Program Information - Heat Weld Systems
View

Details

PARAPET FLASHING FOR PVC

INSIDE CORNER WITH COATED METAL WALL FLASHING FOR PVC
PRE-MOLDED OUTSIDE CORNER FOR PVC

CURB FLASHING FOR PVC
PVC COATED GRAVEL STOP FOR FLEECE BACK
PVC COATED WALL FLASHING

MECHANICALLY FASTENED TARGET ROOF DRAIN FOR PVC
ROOF DRAIN - SUMPS SLOPED MORE THAN 3 inch PER FOOT FOR PVC
ROOF DRAIN FOR DRAIN SUMPS SLOPED MORE THAN 3 inch PER FOOT FOR PVC

EXPANSION JOINT AT JUNCTION OF DECK AND WALL
EXPANSION JOINT CURB TORCH
EXPANSION JOINT WALL TORCH

CONCRETE PAVER WALKWAY
MH-100 PVC Walkway

2 inch OR THICKER INSULATION ATTACHMENT - 8 FASTENERS PER 4ft X 8ft BOARD
FM - 10 Field Fasteners per 4'x8' Board
FM - 6 Field Fasteners per 4'x8' Board
FM - 8 FIELD FASTENERS PER 4ft X 8ft BOARD PATTERN LAYOUT
FM - 8 Field Fasteners per 4'x8' Board
HELIX FOAM ADHESIVE 4" RIBBON PATTERN
HELIX MAX FOAM ADHESIVE 12" RIBBON PATTERN
HELIX MAX FOAM ADHESIVE 4" RIBBON PATTERN
HELIX MAX FOAM ADHESIVE 6" RIBBON PATTERN
INSULATION ATTACHMENT - 12 FASTENERS PER 4ft X 8ft IN FIELD
INSULATION ATTACHMENT - 16 FASTENERS PER 4ft X 8ft IN FIELD
INSULATION ATTACHMENT - 17 FASTENERS PER 4ft X 8ft IN FIELD

FIELD MEMBRANE LAYOUT FOR PVC
ROOF PERIMETER/CORNER CALCULATIONS ELEVATION DIFFERENCE 3ft OR LESS FOR PVC
ROOF PERIMETER/CORNER CALCULATIONS ELEVATION DIFFERENCE GREATER THAN 3ft FOR PVC

FIELD FABRICATED HOT PIPE FOR PVC
FIELD FABRICATED PIPE FLASHING FOR PVC
MEMBRANE COATED METAL PITCH PAN FOR PVC
MOLDED SEALANT POCKET FOR PVC
PREFABRICATED SQUARE TUBING WRAP FOR PVC
PVC PRE-MOLDED PIPE FLASHING
SLEEPER SUPPORT (HEAVY WEIGHT) FOR PVC - OPTION 2
SLEEPER SUPPORT (HEAVY WEIGHT) FOR PVC - OPTION 3
SLEEPER SUPPORT (LIGHT WEIGHT) FOR PVC - OPTION 1

ALL-PURPOSE BAR EDGE TERMINATION FOR PVC
COATED METAL BUTT JOINT FOR PVC
DRIP EDGE FOR ALL PVC SYSTEMS
EDGE TERMINATION - ALL-PURPOSE BAR FOR PVC
GUTTER TERMINATION FOR FLEECE BACK PVC
GUTTER TERMINATION FOR PVC
MEMBRANE COATED GRAVEL STOP FOR PVC
WOOD NAILER ATTACHMENT FOR PVC

"T" JOINT COVER PATCH .060" (60 MIL) OR THICKER MEMBRANES
BACK NAILING PARALLEL WITH SLOPE FOR MODBIT AND FLEECE BACK PVC
FLEECE BACK END LAPS FOR PVC
LAP CROSS SECTION FOR PVC - OPTION 2
METAL RETROFIT - 100 MPH OR LESS WIDE SHEETS WITH SEAMS OVER PURLINS FOR TPO
METAL RETROFIT - 101-120 MHP WIND ZONES MECHANICALLY ATTACHED FOR TPO - OPTION 4
PLATE AND FASTENER PLACEMENT FOR PVC
SEAM INTERSECTION FOR FLEECE BACK PVC
T-JOINT DETAIL 50 MIL MEMBRANE FOR PVC

CONCRETE PARAPET WALL WITH TERMINATION BAR FOR PVC
COPING STONE FOR PVC
CURB/WALL FLASHING WITH COUNTERFLASHING FOR PVC
CURB/WALL FLASHING WITH M-H ALL-PURPOSE BAR FOR PVC
METAL CAP TERMINATION FOR PVC
PREMANUFACTURED ARCHED COPING WITH SPLICE PLATE
PREMANUFACTURED METAL EDGE EXTENDER
PREMANUFACTURED REGLET COUNTERFLASHING
PREMANUFACTURED SURFACE MOUNTED COUNTERFLASHING
REGLET COUNTERFLASHING TERMINATION FOR PVC
SURFACE MOUNTED COUNTERFLASHING FOR PVC
TERMINATION BAR AT CORNER FOR PVC
TERMINATION BAR AT TILT-UP WALL JOINT FOR PVC
TERMINATION BAR FOR PVC
TERMINATION BAR WITH COUNTERFLASHING FOR PVC
TERMINATION ELEVATION CHANGE FOR PVC

MEMBRANE FLASHING TRANSITION TO SHINGLE ROOF FOR PVC
TIE-IN TO EXISTING SINGLE PLY FOR PVC

RIDGE MEMBRANE ATTACHMENT FOR PVC

Specifications

Specification - PVC Systems - PVC Systems KEE Fully Adhered Fleece Back
View
Specification Supplement - AeroWeb Adhesive
View

Guide - Equipment needed to install Heat-Welded Membranes
View
Guide - Insulation Guidelines
View
Guide - PVC Systems HydroBOND Installation Guide
View
Guide - PVC Systems Installation Guidelines
View
Guide - Roof Mounted Photovoltaic Installations
View
Single-Ply Insulation Attachment Guidelines
View
Tech Note - Design Wind Speed vs Warranted Wind Speed
View
Tech Note - Sheet Flutter on Mechanically Attached Systems
View

Options

Item ID Description Packaging Qty per Ctn Weight per Ctn Cover Rate
07MHPKF05G MH PVC KEE HP 105 10X100 FLEECEBACK GRY Shrink Wrap 1 390 1000 Sq.Ft/RL
07MHPKF05T MH PVC KEE HP 105 10X100 FLEECEBACK TAN Shrink Wrap 1 390 1000 Sq.Ft/RL
07MHPKF05W MH PVC KEE HP 105 10X100 FLEECEBACK WHT Shrink Wrap 1 390 1000 Sq.Ft/RL
07MHPKF15G MH PVC KEE HP 115 10X100 FLEECEBACK GRY Shrink Wrap 1 470 1000 Sq.Ft/RL
07MHPKF15T MH PVC KEE HP 115 10X100 FLEECEBACK TAN Shrink Wrap 1 470 1000 Sq.Ft/RL
07MHPKF15W MH PVC KEE HP 115 10X100 FLEECEBACK WHT Shrink Wrap 1 470 1000 Sq.Ft/RL
07MHPKF35G MH PVC KEE HP 135 10X75 FLEECEBACK GRY Shrink Wrap 1 452 750 Sq.Ft/RL
07MHPKF35T MH PVC KEE HP 135 10X75 FLEECEBACK TAN Shrink Wrap 1 452 750 Sq.Ft/RL
07MHPKF35W MH PVC KEE HP 135 10X75 FLEECEBACK WHT Shrink Wrap 1 452 750 Sq.Ft/RL

Videos

FAQs

To reduce blocking, packs should only be stacked 4-packs up to five high. We have found that when stacked higher, the bottom rolls could crush a bit which could create blocking and a wavy sheet when installed. It is possible that the stacking issue can be heightened over the summer months due to the heat.